Start submersible pump troubleshooting with the symptom, alarm history, running liquid level, and discharge path. These checks help separate a control fault, an electrical problem, and a blocked flow path before you choose a repair.
A reset can get a pump running without showing why it stopped. When the same fault returns, site readings tell you more than another reset. A pump that won’t start needs a different set of checks from one that runs but delivers no liquid.
This guide focuses on industrial drainage and wastewater pumps. It also explains where well-pump pressure tanks and single-phase control boxes need their own checks. You’ll find a quick symptom chart, six fault branches, and a list of records to send a service team.
Keep the pump, motor, and controller manuals at hand. Their limits govern lifting, electrical tests, minimum liquid level, and valve use. Use this guide to organize the evidence and choose the right service team; follow the model’s instructions for the work itself.
Key Takeaways
- Save the fault code and time to trip before anyone clears the alarm log.
- Compare flow with head, liquid level, and speed; low flow alone doesn’t prove impeller wear.
- Current, earth leakage, heat, and low-level trips need different checks.
- Qualified staff must handle electrical tests and internal checks under the approved site procedure.
- Close a fault only after the repaired system passes its agreed duty and protection checks.
Start Submersible Pump Troubleshooting Safely

Start with what you can see from a safe place: the control screen, alarm log, gauges, and visible discharge. Don’t open a live panel, reach into a sump, or move a cable to get a reading.
Before clearing debris or opening equipment, authorized staff must isolate all hazardous energy sources. This also applies before lifting a pump or opening pipework. Account for remote start commands, stored electrical energy, trapped pressure, and liquid that could flow back.
Verify isolation under the site’s procedure. A stop button alone doesn’t isolate energy. A pump can start again when a level signal changes, a timer expires, or a remote command arrives.
The OSHA hazardous-energy overview explains the risks from unexpected starts and stored energy during service work. It is a US reference. Apply the rules for your location, and use a separate entry plan for wet wells, including the required permits and rescue arrangements.
Use the specified lifting points and rated lifting gear when pump removal is approved. Never lift a pump by its power cable. Keep a unit with damaged cable insulation or suspected electrical leakage out of service for qualified checks.
Once the fault is resolved, use the submersible pump maintenance checklist to plan routine checks.
Submersible Pump Troubleshooting Chart
Use this chart to choose a fault branch. Each cause is a possibility to check, rather than a finding or permission to restart.
| Symptom | Possible causes | Next evidence or action |
|---|---|---|
| Won’t start, or hums without starting | No start demand, active interlock, supply fault, control fault, jammed impeller | Save demand and fault status; stop a stalled start and arrange qualified checks |
| Runs but delivers no liquid | Low level, closed or blocked discharge, stuck check valve, trapped air, shaft damage | Confirm motor operation, level, and discharge route; stop if no-flow running persists |
| Delivers low flow | Blockage, greater system head, wear, leak, wrong rotation or speed | Compare flow and head at a known speed and liquid level |
| Trips or stops after starting | High current, electrical leakage, overheating, phase fault, low-level trip | Record which protection tripped, the fault code, and time since starting |
| Cycles rapidly or won’t stop | Level-control fault, return flow, pressure-system fault, inflow above removal rate | Compare actual level or pressure with the control system’s demand signal |
| Makes new noise or vibration | Debris, loose support, bearing damage, intake air, cavitation | Note when it occurs; stop for severe vibration or mechanical impact |
Hypothetical example: Morgan, a shift operator, sees a high wet-well level while the duty pump stays stopped. The screen shows a missing start-permissive signal: a required condition hasn’t been met. Morgan saves the alarm log and calls the controls team.
The team checks that signal before anyone approves pump removal. The high level alone hadn’t shown which part had failed. This keeps a control check from becoming an unplanned lifting job.
Why Your Submersible Pump Will Not Start

Check demand, level signals, and interlocks
If a submersible pump is not working, first ask whether the controls are calling for a start. Check the operating mode, start demand, and active stop signals. A standby pump may be healthy but waiting for its start level or turn in the duty sequence.
Compare the displayed level with a separate installed gauge or sensor where one exists. A dirty float, blocked float travel, failed sensor, or wiring fault can prevent a start request. Save photos of safe, accessible displays and note any mismatch without entering the wet well.
Don’t bridge float contacts or bypass protection to prove that the pump runs. A missing permissive may be keeping the motor safe or blocking a start under the wrong conditions.
Separate supply, control, and mechanical faults
Qualified staff can then check the supply, protective devices, contactor, cable, and motor against the wiring diagram and nameplate. Note what changed before the fault. Was there a power cut, cable repair, new controller, or recent pump service?
A motor that hums but fails to reach speed may have a supply fault or a jammed pump. On a suitable single-phase system, the starting parts may also need checks. A hum alone doesn’t prove a failed capacitor. Three-phase systems need a different test route.
Avoid repeated starts on a stalled motor. Inspect the wet end only after safe isolation and removal. Follow the model’s method to check impeller movement, and look for debris or signs of contact. Seal, bearing, and winding work must match that unit’s service instructions.
Why a Submersible Pump Runs Without Enough Flow
The pump runs but delivers no liquid
First confirm that the motor runs. A run command or lit indicator doesn’t prove that the shaft turns or liquid flows. Use installed monitoring and qualified checks to settle that point.
Check the liquid level at the intake while the pump runs. A level taken before starting can hide drawdown, the drop in level caused by pumping. Compare the running level with the model’s minimum level and motor-cooling limits.
Trace the discharge route with drawings and safe, accessible gauges or indicators. A closed valve, reversed or stuck non-return valve, blocked hose, or broken pipe can stop delivery. For groundwater systems, The Driller’s troubleshooting guide lists check-valve faults, trapped air, excessive lift, and low submergence among the causes.
Air trapped in the pump or discharge layout can also stop flow. Follow the installed system’s approved venting method. Don’t drill a vent hole or keep starting and stopping an unfamiliar pump based on advice for another model.
After electrical work on a three-phase unit, qualified staff should check rotation by the manufacturer’s method. If the motor runs but fails to drive the pump, a damaged coupling or shaft may need inspection. Stop persistent no-flow running while the cause is checked.
Flow has fallen below the expected duty
Total dynamic head is the energy the pump adds per unit weight of liquid, expressed in metres. It includes the lift, pressure needs, and flow losses in the system. More resistance or a changed pumping level can reduce flow even when the pump has no damage.
Compare the new readings with an accepted baseline. Use a similar liquid level, discharge condition, and speed. Check the gauges and flowmeter too; a fouled meter can show a false loss of flow.
Hypothetical example: Sam, a plant technician, compares an earlier 100 m³/h reading with a new 70 m³/h reading. Before asking for a new impeller, Sam checks the log. The new test used a lower drive frequency and a different wet-well level.
Sam requests a test with matching conditions. The readings hadn’t yet proved wear. That test can show whether the loss remains when level, speed, and discharge conditions are alike.
If the conditions match, check for inlet deposits, discharge blockages, leaks, and wear within the approved work scope. Changes in the solids can also affect the load. For equipment such as WQ submersible sewage pumps, check the chosen impeller and passage against what is entering the station.
A variable frequency drive (VFD) controls motor speed and adds another check. Its speed command may differ from its output when it limits the load or has a fault. Review the submersible pump VFD guide before proposing a speed change.
Don’t raise speed or throttle a valve as a general fix. Axial- and mixed-flow pumps, in particular, need valve positions and speed limits set by their approved operating procedure.
Why a Submersible Pump Keeps Tripping

Find out which protection tripped before deciding why. Save the exact message and time since starting. Note the liquid level and whether the pump had reached its normal running state.
- Overcurrent or overload: check for binding, a changed duty, supply faults, lost phases, and a mismatch between motor and controller.
- Earth leakage or ground fault: arrange qualified tests of the cable, joints, and motor insulation; check for moisture ingress where the design allows.
- Temperature trip: check the heat signal, cooling conditions, liquid temperature, and load against the model’s limits.
- Low-level or underload trip: check the liquid supply, level signal, and measured load. Confirm what that trip means in the controller manual.
These faults can overlap. A jammed impeller can cause high current and heat. A damaged cable can produce more than one alarm. The first event in the log may help show what caused the later trips.
Don’t assume a fault number means the same thing on every controller. Franklin’s SubDrive/MonoDrive fault FAQs show separate underload, supply, current, open-phase, and short-circuit faults for that product family.
For insulation tests, qualified staff must isolate the motor circuit from the drive and other sensitive electronics as their instructions require. Franklin states that the motor lead must be disconnected from its VFD before the relevant test. Use the equipment’s specified test voltage and resistance limits.
Check cooling as well. A motor below the liquid surface may still lack the cooling flow it needs. The layout, liquid level, temperature, and motor design all matter.
Save any seal-leakage or moisture alarm. Where the sensor sits and how the alarm works determine what it means. It doesn’t, by itself, show which seal has failed.
Don’t fit a larger breaker, bypass leakage protection, or raise an overload setting to keep running. If the cause is still unknown, follow the site’s fault-response plan and send the evidence to the service team.
Check Short Cycling, Continuous Running, and Noise
Frequent starts or a pump that won’t stop
In a wet well, compare actual liquid movement with the start and stop commands. A blocked float, unstable level signal, or narrow gap between start and stop levels can cause repeated starts. A leaking check valve can return liquid after shutdown and start another cycle.
A pump that runs continuously needs a different check. It may be doing its job during high inflow, or it may not be removing enough liquid. Compare inflow, delivered flow, and the level trend before blaming the stop control.
Pressure tanks and pressure switches belong to systems that use them, including domestic wells. Their settings and tank checks don’t transfer directly to wastewater level controls. Get the motor’s allowed number of starts from its manual; there is no single limit for all pumps.
New noise, vibration, or air in the discharge
Note whether the noise follows liquid level, speed, valve position, or incoming solids. Severe vibration, grinding, or repeated impact calls for a stop and service checks under the site procedure.
Debris, worn bearings, loose supports, intake air, and cavitation can produce similar signs. Cavitation occurs when low local pressure lets vapor bubbles form and then collapse. An intake vortex drawing air into the pump is a different cause, though both can disturb flow.
Use the cavitation causes and prevention guide for that specific fault. Minimum submergence means the required liquid cover above a specified pump reference point. That level and the intake clearance depend on the model and site layout. More depth or a new valve position won’t solve every case.
Verify the return to service
After approved repairs, agree what the test must show. Restore guards, connections, valve positions, and control settings under the site procedure. Test the relevant protection and automatic controls while keeping staff clear of unexpected starts.
Record flow, head, liquid level, speed, available electrical readings, and alarms during the agreed test. Compare them with the required duty and equipment limits. A short run without a trip doesn’t prove an intermittent fault has gone.
Submersible Pump Troubleshooting Questions
Why is my submersible pump running but not pumping water?
Possible causes include low liquid at the intake, a blocked discharge, a bad check valve, trapped air, or mechanical damage. Confirm that the motor runs first. Then check the running level and discharge route against the model’s limits. Sound alone doesn’t prove the cause.
Why does my submersible pump keep tripping?
An unresolved fault or protection problem may be causing repeated trips. Find out whether the trip concerns current, leakage, heat, supply, or liquid level. Save the fault log and arrange the right checks before deciding on another start.
Can a submersible pump run in reverse?
A wrongly connected three-phase motor can turn in reverse, and the pump may still deliver reduced flow. Qualified staff should check rotation after relevant electrical work using the model’s procedure. Don’t swap wires on an unidentified single-phase or drive-controlled system.
Should I repair or replace a failed submersible pump?
Base the choice on confirmed damage, repair scope, parts, required duty, and the root cause. Compare repair and replacement on the same duty. A new pump exposed to the same cable fault, abrasive solids, or poor intake conditions may face the same problem.
Before asking for support, collect the pump and motor nameplates, controller model, alarm log, recent changes, and site drawings. Add running liquid level, flow, head, and speed where you have them. Include electrical readings already taken by qualified staff; don’t open equipment to fill a gap.
Keep what you observed separate from what you suspect. “Stops after starting with a temperature alarm” tells a service team more than “motor failed.” Attach clear photos taken from safe places, and list the tests or repairs already done. This helps the next team avoid repeating checks or treating a guess as a finding.
For Kairun equipment or a project-selection review, discuss the operating conditions with Kairun Pump. Good submersible pump troubleshooting links the symptom to evidence, corrects the cause, and verifies the required duty before the fault is closed.